- SPECIALS! SAVE BIG $$ On New and Refurbished Softeners & Filter Systems
- City Water Systems
- Well Water Systems
- Acid Neutralizer Filters
- Fleck 7000 Neutralizers
- CWS 5900e Neutralizers
- Upflow Neutralizers
- Neutralizer Calcite & Parts
- Neutralizer 7500 Series
- Whole House Calcite Cartridges
- Arsenic Filters
- Bacteria Disinfection
- Carbon Backwash Filters
- Chlorination Systems
- Filters & Strainers
- Hydrogen Peroxide Systems
- Irrigation Rust Prevention
- Iron & Manganese Filters
- Metering Pumps & Parts
- Nitrate Filters
- Odor Systems
- Ozone Systems
- Phosphate Crystal Feeders
- RO High Flow
- RO Under-Sink
- Sediment Backwash Filters
- Soda Ash Systems
- Salt-Free Softeners Scale Stoppers
- Tannin Filters
- Ultraviolet Sterilizers
- Ultra Filtration Systems
- Drinking Water Systems
- Filter Media, Chemicals, Valves & Parts
- Filter Tanks & Housings
- Filter Cartridges
- Travel & Emergency Purifiers
- Water Testing
- Commercial Systems
- Water Quality Programs
Calcite Acid Neutralizer 7000-SXT 3.0 CF
Satisfaction Guaranteed! Free Shipping in Continental U.S.
Choose your options:DOWNLOAD INSTALLATION GUIDE!
Add a Free pH Test Kit? Normally $19:
Questions? Get a Fast Answer to your water treatment problems, click here!
|Model||Number of Bathrooms in Home||Flow Rate||Backwash Flow Rate||Dimensions|
|1.0 CF||1 - 2||5 GPM||5 GPM||Diameter: 10" Height: 44"|
|1.0 CF Short||1 - 2||5 GPM||5 GPM||Diameter: 13" Height: 30"|
|1.5 CF||1 - 2||7 GPM||5 GPM||Diameter: 10" Height: 54"|
|2.0 CF||2 - 3||10 GPM||7 GPM||Diameter: 12" Height: 52"|
|2.5 CF||2 - 4||12 GPM||10 GPM||Diameter: 13" Height: 54"|
|3.0 CF||2 - 5||12 GPM||15 GPM||Diameter: 14" Height: 65"|
- Uses the higher quality, more expensive Enpress tank with Vortech distributor which allows the neutralizer media to be backwashed at lower flow rates with less water, saving water and energy.
- All the filter media you need for the system is included.
- Eliminates acidity in the pH range of 6.0 to 6.9 by slowly dissolving Calcite (calcium carbonate) into the water as it flows through the filter.
- Depending on pH and service flow the Calcite bed will need to be replenished periodically with more Calcite.
- Advanced Fleck 7000 electronic backwash control valve valve features fully adjustable backwash and rinse cycles and is loaded with features.
- Reliable electronic control valve provides quick setup and easy programming.
- Quick-connect clips allow easy installation and maintenance.
- High flowFleck 7000 control valve included.
- Environmental cover (NEMA-3R rated) protects control valve from the weather can be installed inside or outside if protected from freezing.
- Full-port Fleck 7000 control valve provides high flow with very little pressure drop.
- Neutralizer 7000-SXT Calcite 3.0 CF: includes inch pipe connectors;
- by-pass valve;
- 3.0 cubic feet of Calcite filter media;
- 14 x 65" filter tank with no top-fill port (this size has no top fill port);
- Fleck 7000-SXT 115v control valve.
- Max pressure recommended is 100 psi.
- Maximum water temperature recommended 100F.
- Filter tank is NSF certified one piece seamless polyester construction for long life.
- Non-corrosive high-tech material construction.
- The recommended maximum flow rate for best performance is 12.0 gallons per minute but peak flow rates of up to 20 gallons per minute are possible.
- The backwash flow rate is 15.0 gallons per minute.
- Filter tank diameter: 14 inches
- Filter tank height: 65 inches
- Height including control valve valve: 71.5 inches.
Which Neutralizer Model Is Best for My Needs?
Neutralizer Filter or Neutralizer Filter Blend?
Choose standard Neutralizer Filter if your pH is between 6 and 6.9.
If your pH is less than 6 or you are not sure, choose one of the "Blend" models above.
What size to get? For most of our customers with homes with 2 – 3 bathrooms and 2 – 6 persons, the 1.5 cubic foot size or the 2.0 cubic foot size is the best choice.
The larger systems can go longer before needing more mineral added to them; however, a 2.5 CF or 3.0 CF neutralizer is rarely needed unless the home is very large and there is a lot of water use.
Professional quality acid neutralizer system comes complete with:
- Calcite media if your pH is 6.0 to 6.9
- Calcite-Corosex blend media if your pH is less than 6.0
- Tank with top fill plug: easy to add media
- Backwash control valve: prevents calcite from turning solid and channeling
- Battery back-up, keeps time of day during a power outage.
- By-pass & blending valve included for ease of use
- Our tanks are semi-transparent: shine a flash light to see depth of calcite inside
- Quality pH Test Kit included, not strips or litmus paper.
- Easy to install. Low maintenance.
- Guaranteed to neutralize pH or your money back.
Which calcite or blend to select?
|Calcite or blend type:||Use to raise pH:|
|Calcite||Use if your pH is from 6.0 to 6.9
Raises pH to 7.0 to 7.5.
|Calcite-Corosex 90%/10% Blend||Use if your pH is from 5.0 to 6.0
Raises pH to 7.0 to 7.5
|Calcite-Corosex 80%/20% Blend||Use if your pH is from 4.5 to 5.0
Raises pH to 7.0 to 7.5
|Corosex||Useful for pH from 4.0 to 6.0
Raises pH to 7.0 to 8.5
Note: usually blended with Calcite
|Common Tank Sizes||Amount of calcite media in tank:|
|9' diameter x 48" height||1.0 cubic foot - 100 lbs|
|10" diameter x 44" height||1.0 cubic foot - 100 lbs|
|10" diameter x 54" height||1.5 cubic foot - 150 lbs|
|12" diameter x 52" height||2.0 cubic foot - 200 lbs|
|13" diameter x 54" height||2.5 cubic foot - 250 lbs|
|Click here to see our selection of Calcite Cartridges. Cartridge sizes available to fit standard 10" filter housings in addition to whole house 'big blue' style filter housings. These are appropriate for point-of-use applications, such as at one faucet, but are not used for correcting the pH for the entire home as the amount of calcite is not sufficient.
Call us TOLL-FREE at 888-600-5426
|Frequently Asked Questions:
Q. What does CF mean?
A. Neutralizers are sold based on the size of the tank. 1.0 CF means 1 cubic foot of calcite is included.
Q. What does a flow sensor do?
A. Optional built-in flow sensor allows neutralizer to backwash based on gallons used. Generally not needed or recommended for neutralizers, but some folks get them if their water usage fluctuates a lot such as for summer cabins or vacation homes.
Q. What is the difference between Calcite and Calcite Blend?
A. Use Calcite neutralizers if your water pH is between 6.0 and 6.9. Use Calcite Blend type if your pH is less than 6.0.
Q. Should I use plain calcite or a blend of calcite and corosex?
A. Generally plain calcite works in most applications (which are in the range of 6.0 to 6.9 pH). if in doubt of your acidic water pH, start with plain calcite. However if you know your pH is less than 6.0, in the range of 5.0 to 6.0, then use a blend of 90% calcite and corosex. This will work in 90% of the applications. In some rare cases if the water is very cold, or if the flow rate is high (a lot of water being used daily) it is OK to use the 80% calcite and 20% corosex.
Q. What is the problem with using a lot more Corosex?
A.Too much Corosex can over-correct the pH and raise the pH up above 8.5. Generally most corrosive water applications (such as for correcting acidic well water for homes with copper pipe etc) work best if the pH is raised to 7.0 to 7.5, which is the most desirable range. It is OK if the pH is up near 8.0 after the neutralizer but not necessary for correcting corrosive water.
Q. Is there any other problem with using too much Corosex?
A. Yes, if too much Corosex is used, the media can cement together and form solid balls of Corosex in the neutralizer. If that happens, the Corosex filter media will not dissolve properly.
Q. What if i add only calcite and find out later that I need to raise my pH to a higher level?
A. This is not a big problem because some Corosex can be added on top of the existing calcite. As long as you don't fill the tank higher than about 2/3rds full it is OK.
Q. How much calcite or calcite-corosex blend media should I buy?
A. See table above to find your tank size. Generally it is rare for most families or home applications to use more than about 50 to 100 lbs a year. If you open up your neutralizer and find it is half-full, just add enough media to raise it to the 2/3rds level and backwash thoroughly.
Q. Does the media go bad? What if I have some left over?
A. No. The media does not go bad. Try to keep it dry and it will keep for many years. Even if its gets wet, it can still be used in most situations.
Q. What is Calcite anyway?
A. Calcite is a high grade of pure crushed and screened white marble limestone media which can inexpensively be used to neutralize acidic or low pH waters to a neutral, less corrosive effluent. Calcite is a naturally occurring calcium carbonate media.
Q. What is the advantage of calcite?
A. One of the advantages of Calcite is its self-limiting property. When properly applied, it corrects pH only enough to reach a non-corrosive equilibrium. It does not overcorrect under normal conditions.
Q. What is Corosex?
A. Corosex® (by Clack) is a highly reactive magnesium oxide, and is used most effectively where pH correction is substantial or high flow conditions are in use. Corosex can be effectively combined with Clack Calcite to combine the high flow neutralization properties of Corosex,along with the slower reacting low flow properties of Calcite, reducing potentially high basic properties due to over correction.
Q. What is the advantage of Corosex?
A. On a per weight basis, magnesium oxide can neutralize much more acidity than can calcium carbonate, (five timesas much). This results in greatly reduced chemical usage for the same pH correction. Please note, under certain low flowconditions, Corosex may overcorrect andcreate a highly basic (high pH) condition. It is better to use it in a 90% calcite to 10% Corosex or 80% calcite to 20% blend.
Q. Are either Calcite or Corosex toxic?
A. No, neither calcite nor Corosex are toxic and are widely used in drinking water. They have been tested and independenlty certified to ANSI/NSF Standard 60.
Q. Is the more expensive Vortech tank necessary?
A. No, the standard heavy-duty neutralizer tank is what we recommend. Vortech tanks have a built-in inner distributor, which you cannot remove. If anything happens to it, or if you accidentally damage it, you have to replace the tank. The standard distributor tube is removal in our regular neutralizer tanks, and we recommend those. However, if you have very low flow from your well, say 4 gallons per minute, there is an advantage to getting the Vortech tank, as it can use 20% to 30% less flow rate. For most wells though, its not needed.
Any other questions? Please email us or call us toll-free at 888-600-5426.
|More information on Calcite Limestone Replacement Media:|
•Naturally occurring material
•Low uniformity coefficient for
maximum contact for controlled pH
•Slower reacting for controlled pH
•Color: Near white
•Bulk Density: 90 lbs./cu. ft.
•Mesh Size: 16 x 40
•Specific Gravity: 2.7
•Effective Size: 0.4 mm
•Uniformity Coefficient: 1.5
•Hardness: 3.0 (Mohs scale)
•Composition: CaCO3, 95% min.
MgCO3, 3.0% max.
CONDITIONS FOR OPERATION
•A gravel support bed is recommended
•Water pH range we recommend for calcite only neutralizers: 6.0-7.0
•Bed depth: 24-30 in.
•Freeboard: 50% of bed depth (min.)
•Backwash rate: 8-12 gpm/sq. ft.
•Backwash Bed Expansion: 35% of
•Service flow rate: 3-6 gpm/sq. ft. but
may be modified to adapt to local
|Calcite is a crushed and screened white marble media which can inexpensively be used to neutralize acidic or low pH waters to a neutral, less corrosive effluent.
Calcite is a naturally occurring calcium carbonate media. One of the advantages of Calcite is its self-limiting property.
When properly applied, it corrects pH only enough to reach a non-corrosive equilibrium. It does not overcorrect under normal conditions. Upon contact with Calcite, acidic waters slowly dissolve the calcium carbonate to raise the pH which reduces the potential leaching of copper, lead and other metals found in typical plumbing systems. Periodic backwashing will prevent packing, reclassify the bed and maintain high service rates. Depending on pH, water chemistry and service flow, the Calcite bed will have to be periodically replenished as the Calcite is depleted.
As the Calcite’s calcium carbonate neutralizes the water, it will increase
hardness and a softener may become necessary after the neutralizing filter, however most of our customers rarely find they need a softener.
Calcite can be effectively combined with Clack Corosex to combine the high flow neutralization properties of Corosex, along with the slower reacting low flow properties of Calcite, increasing the ability to correct low pH.
|More information on Corosex pH Replacement Media:|
|By neutralizing the free carbon dioxide in water, Corosex can correct acidic water conditions and render it less corrosive.
Corosex, being a highly reactive magnesium oxide, is used most effectively where pH correction is substantial or high flow conditions are in use.
pH correction and media consumption are affected by a number of water chemical variables. Being soluble to acidity, Corosex will slowly dissolve and will need to be replenished periodically.
On a per weight basis, magnesium oxide can neutralize much more acidity than can calcium carbonate, (five times as much). This results in greatly reduced chemical usage for the same pH correction.
Please note, under certain low flowconditions, Corosex may over-correct and create a highly basic (high pH) condition. Under certain hardness conditions, pH correction can cause hardness mineralsto precipitate out of solution, resulting in cementing or solidification of the Corosex mineral bed.
|If Corosex is used alone and not in a blend with Calcite, upflow service is generally recommended with hardness exceeding five grains per gallon.
(Always use an in-line filter ahead of an upflow neutralizer to prevent plugging of the lower distribution screen.)
As Corosex’s magnesium oxide neutralizes the water, it will increase hardness and a softener may become necessary after the neutralizing filter.
Corosex can be effectively combined with Clack Calcite to combine the high flow neutralization properties of Corosex, along with the slower reacting lowflow properties of Calcite, reducing potentially high basic properties due to overcorrection.
We recommend Corosex to be blended with Calcite at a ratio or 90% Calcite and 10% Corosex, or 80% Calcite to 20% Corosex. Corosex works better when used with a backwashing neutralizer filter.
|Free Illustrated Report with order: "How to Add Calcite and/or Corosex to Neutralizer Tank Down Flow and Up Flow Systems: Maintenance and Operation Guide "|
Need a new calcite acid pH neutralizer? See our advanced neutralizers here.
Read our report: "How to Treat Acid Well Water" using calcite neutralizers
Read our report: "How to Treat Copper Pipe Corrosion"
See our page on Acid Well Water and Low pH
- 10 year Warranty on the filter tanks. All tanks are NSF Certified & top quality.
- 5 Year Warranty on the control valve. Made in the U.S.A.
- 90 Day money-back guarantee!
Customer Ratings & Reviews
Be the first to rate this item!