Chlorinator Well Water Package J-PRO-22 with Solution Tank
- Finally! A complete easy-to-install well water chlorination system for a Wide Range of Conditions and Well Water. Eliminate odors, bacteria and pretreat iron before filtration.
- These complete chlorinator pump and tank systems include injection check valve, tubing, fittings and are the best way to achieve accurate chlorine residuals with the least amount of maintenance.
- Dual voltage! Works on both 110v or 220v power sources.
J-PRO-22 Well Water Chlorinator Works for a Wide Range of Conditions and Well Water
These complete chlorinator pump and tank systems include injection check valve, 3/8" OD tubing, and fittings and are the best way to achieve accurate chlorine residuals with the least amount of maintenance. Dual voltage! Works on both 110v or 220v power sources.
- Uses chlorine bleach. Easily make your own solution using our Certified Powdered Bleach, or use non-scented liquid chlorine bleach.
- Easy and precise dosage of chlorine makes it easy to control.
- Works over a wide range of water flow rates for most home water wells
- Good for chlorinating well water flow rates from 1 to 50 Gallons Per Minute (1 - 50 GPM)
- Pumps 2.2 to 22 gallons of solution per day
- Works for line pressures up to 110 PSI
- Dual voltage. No need to specify 110V or 220V, works on either voltage.
- Uses only 22 watts of power.
- Dimensions: 5 gallon model: 10" x 10" x 15", height including pump is 26"
- Dimensions: 15 gallon model: 14.5" wide x 24", height including pump is 35".
- Dimensions: 35 gallon model: 18" wide x 33", height including pump is 44".
- Digital speed adjustment makes adjusting the pump fast and easy for accurate injection
- De-gassing valve built-in makes the pump great for chlorination use
- Unlike Stenner-style peristaltic pumps: no pump tube failures, no rollers to go bad, needs less service, and good for continuous duty
- Uses regular household bleach (5% sodium hypochlorite) or liquid pool chlorine (12% sodium hypochlorite) or make your own bleach with powdered calcium hypochlorite.
- These heavy-duty metering pumps systems are designed to last for many years with minimal maintenance.
- Pump easily mounts on the top of the tank or a wall
- Primes super fast, and won't lose often its prime when properly installed
- Complete system includes chlorinator pump, solution tank, injection check valve, tubing, fittings
- The only fitting you need to provide is a 1/2" female threaded port fitting in a tee on your existing piping (available from any hardware store, home depot etc)
- Plug in to a Flow Switch (sold separately) or Wire to your standard pressure switch pump system.
- NOTE: If you have a Variable Speed Well Pump click here for the Proportional Flow Chlorinators.
3 Ways To Turn On and Off Your Chlorinator Automatically
Free Expert Technical Setup and Support
Over 25 years we have installed many hundreds of chlorination systems worldwide. We can offer you expert advice on the exact type of chlorine
solution to use, how much to use and what settings to use
with your new chlorinator. These pumps are the easiest and most accurate chlorinator pumps available on the market today!
Loaded with features only found in much more expensive industrial metering pumps, our J-PRO-22 Metering Pump makes chlorine and other chemical injection fast and accurate. Our easy-to-use installation guide will guide you through the steps, but if you need help or have questions, we are just a phone call or email away.
What is included?
- J-PRO-22 Home Well Water Chlorinator Pump with 5, 15, or 35 gallon heavy-duty polyethylene solution tank
- Tubing (12' feet included) and fittings to connect pump to injection check valve and solution tank
- 1 Injection Check valve 1/2" male pipe thread
- Suction tubing and foot valve to connect solution tank to pump
- Degassing / Priming valve to make it easy to prime pump
- Easy to read Manual
What size solution tank should I order?
- We recommend the 5 or 15 gallon tank. The 5 gallon is convenient due to its size and ease of handling.
- There is usually no home well water application where the 35 gallon tank is needed.
- Most of our customers use 1 to 2 gallons chlorine solution per month.
- There is no advantage to using a larger solution tank in most cases because the chlorine can go bad.
- Mix up enough fresh chlorine solution to last for 3 months as chlorine can lose its strength over time.
- 5 Gallon Solution Tank Dimensions: 15.8" Diameter x 11" x 17.5" Height
- 15 Gallon Solution Tank Dimensions:14.5" Diameter x 31" Height
- 35 Gallon Solution Tank Dimensions: 18" Diameter x 40" Height
What type of bleach should I use?
- We recommend using NSF certified 10% or 12% liquid bleach if available.
- This is often sold as liquid pool chlorine at home stores, pool companies and hardware stores
- Do not use household laundry bleach, as it contains additives
- You can use liquid bleach as long as it is free of additives
- We also sell chlorine granules and you can make up your own bleach but the cost is much higher than liquid bleach.
- To use just add 1 oz of powder to 1 gallon of soft or purified water to make up your solution
- Stores for up to 8 to 12 months in cool dark dry location.
Should I use a contact retention tank?
- In most cases it works best to use a contact tank. Contact Retention Tanks are a great way to allow sufficient contact time after your system has injected chlorine or peroxide.
- A contact tank provides contact time to kill bacteria, oxidize iron, odors etc.
- Provides settling of sand and grit and makes it easy to drain down and flush out heavy particles
- Use less chlorine
- Eliminates heavy chlorine tastes and odors by allowing chlorine to react with iron, odor or bacteria in water
- See our line of contact tanks here. We recommend the 1054 size OR the 1354 size for most homes.
Will I smell or taste the chlorine? What about my septic tank?
- You can easily adjust the chlorine residual in the water so it is similar to city water and contains very low levels, less than 1.0 PPM
- For best results however we recommend a carbon whole house filter.
- As an option you can use a low cost refillable carbon cartridge, or self-cleaning backwash carbon filter.
- The carbon whole house filters remove any trace of chlorine so no chlorine enters your household water or septic tank.
- A contact retention tank also reduces the amount of chlorine after injection as it gives a few minutes for the chlorine to do its job and dissipate.
Whole House Package w/ Contact Tank
What is the warranty? How long do these systems last?
- The system includes a one year manufacturer warranty.
- You can usually expect 4 to 6 years life however all components are serviceable and replaceable.
- Use purified or soft water to make up your chlorine solution and follow recommended routine maintenance for best results.
Can I install this myself? Can I have my plumber or handyman install it?
- Yes, you can install it yourself, however a local plumber or handyman can also install it for you.
- In addition to the easy to read manual, we also have youtube videos that walk you through the installation. JPRO Install Video
- To make it easier for a plumber or handyman to install we recommend the optional Schedule 80 PVC Injection Tee (see drop down menu) and if you want to avoid having to do any wiring we recommend the optional pre-wired flow switch.
- The chlorinator typically takes about 2 - 3 hours to install.
1 Year Warranty from date of delivery.
If your pump
fails under warranty, please call or email our office to obtain a Returns Good
Authorization Number before sending us back the pump for repair or replacement
under the warranty. No returns can be accepted without an RGA number.
The Warranty covers repair
and/or replacement of the metering pump but not shipping costs.
While defects are
rare, we do our best to respond to warranty returns fast as we can. Please
allow 3 to 5 business days after pump has been returned for your pump to be
repaired or a new one supplied under the warranty agreement.
If the water supply
and its continuous chlorination are critical, a back-up chlorinator pump should
be on hand. Shipping charges are not covered under warranty.. Any
expedited shipping (overnight, 2-day, etc.) is the customer�s responsibility.
Conditions Not Covered by the Warranty:
Power surges or outages that
cause pump failure are not covered under warranty.
protection is strongly recommended. If a pump is returned for warranty
replacement and the cause of failure is determined to be from a voltage spike,
the pump does not qualify for replacement. This is the leading cause of
failure. Pump failure during, or because of, power failure is not covered under
This pump is
intended for indoor use only. The pump must never be exposed to freezing
temperatures, direct sunlight, or rain. If the cause of failure is determined
to be from exposure to any of these environments, the pump does not qualify for
replacement and will not be covered under warranty.
3 Options to Install Your Chlorinator To Turn On Automatically
Detailed printed installation instructions are included with each order.
Option 1: WIRE TO WELL PUMP PRESSURE SWITCH
Wire to your well's pressure switch. This is the lowest cost method. Simply install a dedicated wall outler, that is wired in to the existing pressure switch and powered up whenever the well pump turns on (and off)
Option 2: PRE-WIRED FLOW SWITCH
Install a flow switch. This makes it fast and easy. No electrical wiring to do and any plumber, or person familiar with basic plumbing can install the chlorinator. No electrician required or electrical wiring to do.
Simply install the pre-wired flow switch. Plug the flow switch into a standard 120v wall outlet. Then, plug the chlorinator pump into the electrical outlet on the flow switch. Whenever there is flow, the metering pump will then turn on.
Option 3: PROPORTIONAL-FEED FLOW METER TYPE
Use a proportional-fee type of installation. This is also very easy to set up and requires no electrical wiring or electrician to install the system. A flow meter is installed which tursn on and off the chlorinator pump based on the flow of water.
As soon as there is flow of water through the meter, the chlorinator pump will pump faster or slower based on the amount of water flowing through the flow meter
Simply install the flow meter and connect the cable to the chlorinator pump. Plug the chlorinator pump into a standard 120V wall outlet. When the water flows, the pump will pump more or less chlorine based on how fast the water is flowing.
NOTE: Unlike Option 1 and Option 2, there is no need ot install the injection check valve before your pressure tank. With the proportional-feed type of installation, the injection check valve can be installed AFTER the pressure if desired.